The Loong Boat Festival is coming, and Zongzi is about to make a grand debut. For large-scale manufacturers, it is time to stock up. But in the face of large orders, cleaning the leaves of zongzi is a key link. Zongye generally grows in the wild and is covered in a lot of dust. Manual cleaning is labor-intensive and time-consuming. Herd Machinery has launched a Zongye cleaning machine to solve your problem.
The brown leaf cleaning machine consists of an auxiliary leaf section, a brush cleaning spray section, and a clean water spray section. The soaked brown leaves are manually laid on the leaf laying section, which is composed of a mesh belt driven by power. The mesh belt transports the brown leaves to the brush cleaning spray section. There is a certain speed difference between the upper and lower brush rollers, which creates a certain rubbing force when cleaning the brown leaves. This simulates the same effect of human action as hand scrubbing. The brown leaves are cleaned by a brush in the spray section and then enter the mesh belt conveyor section. The Hede Mechanical Zongye Cleaning Machine is easy to install, maintain, and has low energy consumption, greatly saving labor and improving work efficiency.
Normal operating conditions for palm leaf cleaning machine:
The ambient temperature should be between 0-40 degrees Celsius, and the average temperature within 24 hours should not exceed 35 degrees Celsius. There should be no excessive acid, salt, or corrosive gases in the air. At lower temperatures, higher humidity is allowed, and attention should be paid to condensation that may occur accidentally due to temperature changes (for electrical components). The altitude shall not exceed 2000 meters.
Operation and maintenance
1. The operation of the palm leaf cleaning machine should be the responsibility of a dedicated person.
It is strictly prohibited to touch the transmission rollers and components with hands during operation to ensure safety!
2. Fill the water tank with water and observe if the water pump is running normally (refer to the water pump manual).
3. Pay attention to observing whether the brown leaf cleaning machine is operating normally.
4. After daily production, any debris adhering to the palm leaf cleaning machine should be promptly removed. It is strictly prohibited to rinse the water pump, reducer, transmission mechanism, and electrical control box with water. Before cleaning, make sure to turn off the device and have someone monitor the electrical switch. It is strictly prohibited to turn it on during cleaning!
5. Check the tension condition of the transmission chain every month and lubricate the chain transmission device once. Before maintenance, it is necessary to confirm the shutdown and have someone monitor the electrical switch. It is strictly prohibited to close the switch during maintenance!
6. After running for 5000 hours, disassemble and wash the rolling bearings and replace the lubricating grease. Those with severe wear should be replaced.
7. Change the oil for the reducer once a year.
The brown leaf cleaning machine consists of an auxiliary leaf section, a brush cleaning spray section, and a clean water spray section. The soaked brown leaves are manually laid on the leaf laying section, which is composed of a mesh belt driven by power. The mesh belt transports the brown leaves to the brush cleaning spray section. There is a certain speed difference between the upper and lower brush rollers, which creates a certain rubbing force when cleaning the brown leaves. This simulates the same effect of human action as hand scrubbing. The brown leaves are cleaned by a brush in the spray section and then enter the mesh belt conveyor section. The Hede Mechanical Zongye Cleaning Machine is easy to install, maintain, and has low energy consumption, greatly saving labor and improving work efficiency.
Normal operating conditions for palm leaf cleaning machine:
The ambient temperature should be between 0-40 degrees Celsius, and the average temperature within 24 hours should not exceed 35 degrees Celsius. There should be no excessive acid, salt, or corrosive gases in the air. At lower temperatures, higher humidity is allowed, and attention should be paid to condensation that may occur accidentally due to temperature changes (for electrical components). The altitude shall not exceed 2000 meters.
Operation and maintenance
1. The operation of the palm leaf cleaning machine should be the responsibility of a dedicated person.
It is strictly prohibited to touch the transmission rollers and components with hands during operation to ensure safety!
2. Fill the water tank with water and observe if the water pump is running normally (refer to the water pump manual).
3. Pay attention to observing whether the brown leaf cleaning machine is operating normally.
4. After daily production, any debris adhering to the palm leaf cleaning machine should be promptly removed. It is strictly prohibited to rinse the water pump, reducer, transmission mechanism, and electrical control box with water. Before cleaning, make sure to turn off the device and have someone monitor the electrical switch. It is strictly prohibited to turn it on during cleaning!
5. Check the tension condition of the transmission chain every month and lubricate the chain transmission device once. Before maintenance, it is necessary to confirm the shutdown and have someone monitor the electrical switch. It is strictly prohibited to close the switch during maintenance!
6. After running for 5000 hours, disassemble and wash the rolling bearings and replace the lubricating grease. Those with severe wear should be replaced.
7. Change the oil for the reducer once a year.
